![\"Roundhouse](\"https:\/\/thenscaler.com\/wp-content\/uploads\/2015\/02\/roundhouse_pieces.jpg\")
<\/a>Roundhouse in pieces<\/p><\/div>\n
The damage could have been a lot worse; mostly it came apart at glue joints. A little breakage, but not much. I originally built this twenty years ago as an exterior model; no interior lighting or details. It was nicely enough colored that it worked well unpainted (though I intended to get to that…. some day). No anti-crazing glue was available in those days, so the windows which look fine on the outside look atrocious on the inside.<\/p>\n
Decisions, Decisions<\/h2>\n
The model did not have the common decency to completely disassemble itself, which would have made this much easier, so I had some choices to make. In contrast to the glue joints that failed, the rest were showing no signs of giving up easily.<\/p>\n
First and most obvious was whether to rebuild the 6th bay, since most major pieces were intact. For the sake of the space available on the L&NC<\/a>, cutting back to 5 bays makes sense without diminishing the impact of this model. I could have gone to 4, but the broken frame for the 5th bay door presented a nice weathering opportunity, which we’ll see later.<\/p>\n Secondly, what kind of lighting and how? I was thinking incandescent, and hanging lights would be authentic, so some sort of hanging lamp with an industrial style shade seemed like a good idea. I found both led and incandescent options; I decided to try the incandescent type.<\/p>\n Removing the floor turned out to be the easiest way to open up the model, so I decided to reconstruct the model with a solid top structure that is removable from a separate base. Putting aside the floor, I reassembled the top structure, leaving one roof section off where I planned to route wiring.<\/p>\n Main structure, partly reassembled<\/p><\/div>\n That decision, along with the intended orientation on the L&NC, spawned a few other choices.\u00a0 Now, when in operation, the interior will be viewable primarily through the doors and secondarily through the windows and skylights. Since the most open sight line will be through the doors toward the back, I decided to attempt some improvement of interior finish along the back wall.<\/p>\n Painted Interior Window Castings<\/p><\/div>\n I pried off the clear styrene, which was as difficult as I would have expected, requiring some grinding and sanding to get rid of stubborn bits holding on to the green window part.\u00a0 Then I painted the window part brick, leaving muntins and a thin window frame green. Having done the back wall I re-evaluated the other sight lines and concluded that removing the glazing elsewhere was probably not worth the trouble (I’ll keep that option open for later).<\/p>\n Light coming through simulated glass.<\/p><\/div>\n Since the glazing was gone, I decided to try using Testors Clear Parts Cement & Window Maker to make ‘glass’ in one pair of rear windows. It was easy enough to do if you follow the instructions, and the effect is interesting.\u00a0 I probably used a little too much, but the material seems to have a lens effect in windows this small. This simulates older glass nicely, but does not create a “see-through” window (for purposes of viewing the interior). The way the Roundhouse will be oriented on the L&NC<\/a>, the back window will face a blocked (by the furnace) area, so you will not be able to directly look through these windows in any case. So I think I will do the rest of the rear windows the same way.<\/p>\n Model paint is notoriously expensive (over $5 per oz, discounted) and, frankly, nothing special beyond formulating specific colors that duplicate prototype colors. In this respect I’m lucky there is no convenient hobby shop here; that has forced me to look to other solutions which, to my delight, are vastly cheaper.<\/p>\n Liquitex BASIC Acrylic Paint (available at all major art\/craft store and on Amazon), at $5 per 4 oz tube (cheaper in even larger quantities, or sets) is a good deal.\u00a0 It is available in a wide range of standard artists colors that are easily mixed to create any color you want (just keep track of the formula!). These are formulated for general artist use so they are thicker than standard model paints. I mix small amounts of paint with acrylic thinners to get whatever consistency I want.<\/p>\n My brick color is a simple mix of 50%Red Oxide and 50% Burnt Umber. My color for light colored mortar, masonry, stone and concrete is Titanium White with 5% Yellow and 5% Grey (a 50% Grey) – basically a dab of each into a larger amount of white.<\/p>\n I found some Miniatronics parts, counter-intuitively called “Lamp Shade with Bulb,” that I thought would make good hanging lamps for the interior, so I bought 10 of them from Hobbylink.<\/p>\n Miniatronics ‘Lamp Shade with Bulb”<\/p><\/div>\n Here two are mounted in 1\/8″ Styrene u-channel that has been painted Floquil Weathered Black (from my limited collection of old paints) to match the interior girders. To size them, I studied the interior clearances relative to locomotives and realized that clearance was limited in the tall section, and non-existent in the shorter fore and aft bay sections.<\/p>\n Hanging Lamps in Bay 1<\/p><\/div>\n My feeling at that point was these lamps were not suitable for the short sections, since they would not be visible mounted up against the ceiling. That feeling increased after mounting and lighting the first pair.<\/p>\n Miniatronix Lamp Shade with Lamp – Lit<\/p><\/div>\n <\/p>\n I guess I should not have expected much from a 1.5 volt 30mA lamp.\u00a0 Still, I’d hoped it would cast more light than that! As a decorative lamp it works fine at N scale – you get little peaks of them if you look in and they seem right. For casting light on the broader scene, even if I doubled up on them, another solution is needed.<\/p>\n I’d already been working with Addressable RGB LED<\/a> strips as a solution to bringing light to the layout, and it occurred to me that adding ALEDS as a hidden light source would allow me to more fully light up the interior. So that is what I did.<\/p>\n RGB LEDS for General Lighting<\/p><\/div>\n The individual pads are cut from a 5 meter strip and wired together with 30 GA wire. As you can see from the picture of the completed interior below, there are 10 of them with addresses 0 to 9.<\/p>\n Soldering Addressable LEDS<\/p><\/div>\n To solder the very thin wire to the pads, I taped the leads down and slipped the pads underneath. That was more than stable enough to make the soldering fairly easy.\u00a0 This particular LED is #0, so the left hand leads are heavier (22ga) for incoming power and data (for durability and handling), and the right hand leads out to the rest of the strand.<\/p>\n I fabricated the strand in two halves with 5 LEDS each, soldering leads from the two halves together during installation. Each half strand had to be carefully threaded through the girders.\u00a0 I did break – and repair – a couple of connections the first time I tried.\u00a0 After I got them threaded successfully, I glued the pads down to the styrene roof with dabs of Liquid Nails for Projects<\/a> (low VOC, foam safe). You can bet I tested the\u00a0 lights before gluing them down!<\/p>\n Completed Roundhouse, from below<\/p><\/div>\n The LED wiring is simple and efficient – 1 connection to a digital pin on the Arduino, plus 1 wire each for power and ground.\u00a0 The incandescent lamps were more complicated since I had no intention of giving over 10 pins on the Arduino. Further, turning them on and off individually was not necessary, so I decided to run them in “bay pairs.” Unfortunately, the 60 mA draw of a pair of these is more than you want on an Arduino pin, so that meant some sort of relay or transistor would be necessary to switch the current.<\/p>\n Current isn’t the only problem: there aren’t enough digital pins on an UNO to control everything I have planned.\u00a0 So a pin preservation strategy is called for.<\/p>\n I decided to use a 74HC595 serial-in-parallel-out shift register. One data pin plus two timing pins (total of 3 pins) allow an Arduino to control 8 digital outputs<\/a>; additional shift registers can be wired in series to extend the total number of outputs available without additional Arduino pins. The parallel output of these chips means that after the Arduino sends instruction bits serially, all the outputs are turned on or off at the same time (parallel output), a useful property for animation and lighting control.<\/p>\n Because of the higher current (and also different voltage) of the lamps, I put a UNL2803 darlington array — a transistor array that can sink<\/strong> <\/em>high current — between the shift register and the lights. The only downside of a darlington is some current loss.<\/p>\n Both chips are inexpensive, running about $.60 each in small quantities at digikey.\u00a0 Now that I’ve worked with them I’d say they are very useful basic parts for the Arduino enthusiast.<\/p>\nGetting Started<\/h2>\n
<\/a><\/a><\/a>Paint Cheapskate<\/h2>\n
Installing Lights, Round 1<\/h2>\n
<\/a><\/a><\/a>Addressable LEDS<\/h2>\n
<\/a><\/a><\/a>\u00a0A Shift Register and a Darlington Array<\/h2>\n